Are you new to using weed eaters? If so then you can get some helpful information from various sites such as The Weed Eater Geek. In particular, such sites can provide guidelines about how to pick a weed whacker, and reviews about different models on the market.
However, it’s also important to avoid certain common mistakes when operating the string trimmer. That, in turn, will help the unit to work as effectively as possible whether it’s around a yard, in a garden, or along a road. Here are some of the top mistakes to avoid:
- Not leaving 2-inches of weeds
As you might learn from The Weed Eater Geek it’s important to avoid trimming the weed all the way down to the ground. There are various reasons. One of the main ones is that you’ll make a mess by “trimming” the dirt, which can quite messy. The situation can be even worse if it rained recently and the nylon string is spinning through the mud. That’s definitely a situation you’ll want to avoid.
There’s also the issue that the nylon string can be damaged when it keeps striking dirt instead of weeds and similar plants. Besides dirt being denser than weeds can be exponentially so when there hasn’t been any rain for a while. In that situation, the dry soil can be quite on your nylon string. As a result, you’ll likely have to replace the string sooner rather than later, which can be quite expensive if you have to replace the string over and over again.
- Not removing big rocks before you start
It would be quite tough to remove every single pebble in the regions where you’ll be using the weed eater. However, medium and large sized rocks can be quite tough on the nylon string. Within the time it can wear down the string faster and require you to replace the spool faster.
Another problem with larger rocks is that they can fly into the air when the string hits them. That, in turn, can cause a safety issue that you’ll likely want to avoid. The solution is to take the time to remove the larger rocks around the area you’ll be trimming to make sure your work will be done as safely as possible.
- Not stopping when you’re tired or sore
It’s safe to say that a weed eater isn’t the heaviest power tool on the market. It’s also quite light compared to using a lawn mower and doesn’t require you to push or pull the unit. However, you might have a health issue or be required to operate the lawn mower on a hot/humid summer day, for example.
As always it’s important to listen to your body. If you feel overly sore or there’s another problem make sure to stop trimming the area immediately. If your body becomes overly sore then it’s critical to stop immediately and get a checkup with your doctor if the situation is bad enough.
That’s also the case if you start suffering from heat exhaustion. In that, you should also stop immediately, get hydrated, and rest until you’re ready to start again. Sometimes your energy and fluids are drained faster than you realize when the weather is quite hot and/or humid. In that case, it’s important to refuel with water and a salty snack to add electrolytes you lost during the work.
- Not releasing more string for thicker weeds
If you have to cut through thicker weeds or other plants it’s important to use more string. That will add more force to cut the weeds or other small plants. That, in turn, will help to conserve your nylon string. On Some units include a button to do this task automatically while others require you to do the task manually.
It’s important to take such steps to help your spool of nylon string to last longer. If the other hand if it gets worn down faster it could cost you a small fortune if you have to keep replacing the string.
- Not using a steady, forward/side-by-side movement
This is the type of movement you should use in order to get the best results. It’s important for the movement of the weed eater to be as smooth as possible instead of using abrupt movements. That will make cutting the weeds, shrubs, etc. as smooth as possible.
Another important tip is to make sure that the movement you use is forward and side-to-side. That’s another important step to take in order to ensure that the cutting is optimized. For example, it’s important to move side-to-side instead of back-and-forth. It will help to produce the best results when trimming the area. This approach is one that’s been developed by experts who are familiar with the best operation of the string trimmers.
- Not checking the gas/cord/battery
After finding a weed eater that’s right for you from sources such as The Weed Eater Geek it’s important to make sure the power source is prepared before you start using the power fool. If you’re using a gas model make sure that it’s filled up with fuel. You won’t want to learn it requires gas in the middle of your trimming. That’s especially true if you have to buy gas several miles away.
If you’re using an electric-powered weed whacker you found online to make sure there aren’t any issues with the cord. In particular, make sure that the cord is plugged in properly to the outlet and you have enough extension cord. That will help to keep the string trimmer powered up when you use a “green” unit to spruce up a yard or garden.
Finally, if you’re using a battery-powered weed whacker it’s important to make sure the battery is fully charged before you get started. Depending on how much area you have to trim you might want to consider having a spare battery on hand as well.
These are some common mistake to avoid after you pick a weed whacker for your needs. You can also get a lot of helpful information from sites such as The Weed Eater Geek.